This page is automatically generated from ecmd_defs.m4 and wiki.m4 which are part of the Ethersex source code repository. Do not edit this page but send pages for those files!
Network configuration
| Command syntax
|
Short description
|
| mac xx:xx:xx:xx:xx:xx
|
Set the MAC address.
|
| show mac
|
Display the MAC address.
|
| show ip
|
Display the IP address.
|
| show netmask
|
Display the network mask.
|
| show gw
|
Display the IP address of the default router.
|
| show version
|
Display the version number.
|
| ip IP
|
Set the IP address.
|
| netmask IP
|
Set the network mask.
|
| gw IP
|
Set the address of the default router.
|
Resetting the controller
| Command syntax
|
Short description
|
| reset
|
Reset the Ethersex.
|
| wdreset
|
Go into endless loop to trigger a watchdog timeout.
|
Stella commands
| Command syntax
|
Short description
|
| stella store
|
Store values in eeprom
|
| stella load
|
Load values from eeprom
|
| channels CHANNELS
|
Return stella channel size
|
| stella version STELLAVERSION
|
Get stella protocol version
|
| stella fadestep set FADESTEP
|
Set stella fade step
|
| stella fadestep get
|
Get stella fade step
|
| channel set CHANNEL VALUE
|
Set stella channel value
|
| channel get CHANNEL
|
Get stella channel value
|
| bootloader
|
Call the bootloader.
|
Port I/O
| Command syntax
|
Short description
|
| io set ddr PORTNUM HEXVALUE [MASK]
|
Set the DDR of port PORTNUM to VALUE (possibly using the provided MASK).
|
| io get ddr PORTNUM
|
Display the current value of the DDR PORTNUM.
|
| io set port NUM HEXVALUE [MASK]
|
Set the PORT NUM to VALUE (possibly using the provided MASK).
|
| io get port NUM
|
Display the current value of the PORT NUM.
|
| io get pin PORTNUM
|
Display the current value of the PIN-register of the port PORTNUM.
|
| io get mask PORTNUM
|
Display the mask of the port PORTNUM.
|
| c6 get VARNAME
|
Display the current value of the ECMD_GLOBAL Variable
|
| c6 set VARNAME VALUE
|
Set an new value on the ECMD_GLOBAL Variable
|
Named Pin
| Command syntax
|
Short description
|
| pin get NAME
|
Read and display the status of pin NAME.
|
| pin set NAME STATUS
|
Set the status of pin NAME to STATUS.
|
| pin toggle NAME
|
Toggle the status of pin NAME.
|
HD44780 LCD Display
| Command syntax
|
Short description
|
| lcd clear [LINE]
|
Clear line LINE (0..3) or the whole display (if parameter is omitted)
|
| lcd write TEXT
|
Write TEXT to the current cursor location
|
| lcd goto LINE COL
|
Move cursor to LINE and column COL (origin is 0/0)
|
| lcd char N D1 D2 D3 D4 D5 D6 D7 D8
|
Define use-definable char N with data D1..D8 (provide DATA in hex)
|
| lcd init CURSOR BLINK
|
Reinitialize the display
|
| lcd shift DIR
|
Shift the display to DIR (either left or right)
|
Dallas 1-wire
| Command syntax
|
Short description
|
| 1w list
|
Return a list of the connected onewire devices
|
| 1w get DEVICE
|
Return temperature value of onewire DEVICE (provide 64-bit ID as 16-hex-digits)
|
| 1w convert [DEVICE]
|
Trigger temperatur conversion of either DEVICE or all connected devices
|
DNS
| Command syntax
|
Short description
|
| nslookup HOSTNAME
|
Do DNS lookup for HOSTNAME (call twice).
|
| show dns
|
Display the IP address of the configured DNS server.
|
| dns IPADDR
|
Set the IP address of the DNS server to use to IPADDR.
|
SYSLOG
| Command syntax
|
Short description
|
| syslog STRING
|
Send string to syslog server.
|
| show syslog
|
Display the IP address of the configured SYSLOG server.
|
Clock
| Command syntax
|
Short description
|
| time
|
Display the current time.
|
| date
|
Display the current date.
|
| whm
|
Display the uptime.
|
ADC
| Command syntax
|
Short description
|
| adc get [CHANNEL]
|
Get the ADC Value in HEX of CHANNEL or if noch channel set of all channels.
|
KTY
| Command syntax
|
Short description
|
| kty get [CHANNEL]
|
Get the temperature in xxx.x °C of CHANNEL or if noch channel set of all channels.
|
| kty cal get
|
Return the calibration difference to 2k2 Resistor.
|
| kty autocalibrate CHANNEL
|
Calibrate to 1000 Ohm precision Resistor.
|
Dataflash
| Command syntax
|
Short description
|
| df status
|
Display internal status.
|
| fs format
|
Format the filesystem.
|
| fs list
|
List the directory.
|
| fs mkfile NAME
|
Create a new file NAME.
|
| fs remove NAME
|
Delete the file NAME.
|
| fs truncate NAME LEN
|
Truncate the file NAME to LEN bytes.
|
| fs inspect node NODE
|
Inspect NODE and dump to serial.
|
| fs inspect inode INODE
|
Inspect INODE (and associated page).
|
SD/MMC Card Reader
| Command syntax
|
Short description
|
| sd dir
|
List contents of current SD directory.
|
RFM12
| Command syntax
|
Short description
|
| rfm12 status
|
Display internal status.
|
| rfm12 setbaud BAUD
|
Set baudrate to BAUD.
|
| rfm12 setbandwidth BW
|
Set RX bandwidth to BW.
|
| rfm12 setmod MOD
|
Set modulation to MOD.
|
| rfm12 setgain GAIN
|
Set preamplifier gain to GAIN.
|
| rfm12 setdrssi DRSSI
|
Set the drssi to DRSSI.
|
| rfm12 tevion
|
housecode command delay cnt
|
| rfm12 2272
|
housecodeCommand delay cnt
|
| rfm12 external filter
|
Toggel receiver
|
Miscelleanous
| Command syntax
|
Short description
|
| d ADDR
|
Dump the memory at ADDR (16 bytes).
|
| help
|
List which commands are available.
|
DC3840 Handycam support
| Command syntax
|
Short description
|
| dc3840 capture
|
Make a picture
|
| dc3840 send A B C D E
|
Send provided command bytes to the camera.
|
| dc3840 sync
|
Re-sync to the camera
|
| pwm
|
start pwm
|
I2C (TWI)
| Command syntax
|
Short description
|
| i2c detect
|
list detected I2C Chips
|
| lm75 ADDR
|
Get temperature
|
| pca9531 ADDR PERIODPWM1 DUTYPWM1 PERIODPWM2 DUTYPWM2 LED0..3 LED4..7
|
set PWM1 and PWM2 and LED states
|
| pcf8574x read ADDR CHIP
|
Get bits
|
| pcf8574x set ADDR CHIP HEXVALUE
|
Set bits
|
| eeprom reinit
|
Force reinitialization of the EEPROM config area
|
FS20 Befehl
| Command syntax
|
Short description
|
| fs20 send Hauscode Adresse 0x00
|
turn off
|
| fs20 send Hauscode Adresse 0x01
|
an, 6,25% Einschalten auf Helligkeitsstufe 1 (min.)
|
| fs20 send Hauscode Adresse 0x02
|
an, 12,5% Einschalten auf Helligkeitsstufe 2
|
| fs20 send Hauscode Adresse 0x0f
|
an, 93,75% Einschalten auf Helligkeitsstufe 15
|
| fs20 send Hauscode Adresse 0x10
|
an, 100% Einschalten auf Helligkeitsstufe 16 (max)
|
| fs20 send Hauscode Adresse 0x11
|
an, alter Wert Auf letztem Helligkeitswert einschalten
|
| fs20 send Hauscode Adresse 0x12
|
toggle Wechsel zwischen “aus” und “an, alter Wert“
|
| fs20 send Hauscode Adresse 0x13
|
dim up Eine Helligkeitsstufe heller
|
| fs20 send Hauscode Adresse 0x14
|
tdim down Eine Helligkeitsstufe dunkler
|
| fs20 send Hauscode Adresse 0x15
|
dim up and down ..., + bis max, kurz warten, - bis min, kurz warten,
|
| fs20 send Hauscode Adresse 0x16
|
timeset Timerprogrammierung (Start, Ende)
|
| fs20 send Hauscode Adresse 0x17
|
send status Nur bei bidirektionalen Komponenten!
|
| fs20 send Hauscode Adresse 0x18
|
aus, für Timerzeit
|
| fs20 send Hauscode Adresse 0x19
|
an, 100%, für Timerzeit
|
| fs20 send Hauscode Adresse 0x1A
|
an, alter Wert, für Timerzeit
|
| fs20 send Hauscode Adresse 0x1B
|
reset (auf Auslieferzustand)
|
FS20 CODE
| CODE'
|
BERECHNUNG'
|
| HAUSCODE
|
Hauscode (12341234) Von allen Ziffern "1" abziehen (01230123) -> BC (obase=16,ibas=4) 0x1B1B
|
| ADRESSE
|
ADRESSEGRUPPE/Unteradresse (2222 ) Von allen Ziffern "1" abziehen (1111) -> BC (obase=16,ibas=4) 0x55
|
| Lokaler Master (Adresse)
|
ADRESSEGRUPPE/Unteradresse (2244 ) Von allen Ziffern "1" abziehen (1133) -> BC (obase=16,ibas=4) 0x5F
|
| Globaler Master (Adresse)
|
ADRESSEGRUPPE/Unteradresse (4444 ) Von allen Ziffern "1" abziehen (3333) -> BC (obase=16,ibas=4) 0xFF
|
ECMD mit BROWSER
| h t t p ://IP-ETHERSEX/ecmd?show+ip'
|
