Ecmd Reference: Unterschied zwischen den Versionen

Aus Ethersex_Wiki
Wechseln zu: Navigation, Suche
(Importing text file)
(Importing text file)
 
(37 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 5: Zeile 5:
  
 
__NOTOC__
 
__NOTOC__
 +
== Analog/Digital Conversion ([[ADC]]) ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| adc get  [CHANNEL]
 +
|  Get the ADC value in hex of CHANNEL or if no channel set of all channels.
 +
|-
 +
| hr20 temp
 +
|  Read HR20 temperature sensor.
 +
|-
 +
|}
 
== DNS Resolver ==
 
== DNS Resolver ==
 
{| border='1'
 
{| border='1'
Zeile 30: Zeile 42:
 
| tlc5620  `[CHANNEL] [VALUE]
 
| tlc5620  `[CHANNEL] [VALUE]
 
|  Set Output to value (Value: 0-0xff)'
 
|  Set Output to value (Value: 0-0xff)'
 +
|-
 +
|}
 +
== Fnordlicht ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| fnordlicht  "ADDRESS RED
 +
| GREEN,BLUE",fnordlicht command to set RGB color
 +
|-
 +
| fnordlicht_init
 +
| fnordlicht init
 
|-
 
|-
 
|}
 
|}
Zeile 36: Zeile 60:
 
| ''Command syntax''
 
| ''Command syntax''
 
| ''Short description''
 
| ''Short description''
 +
|-
 +
| hr20 hourbar  START STOP
 +
|  Update hourbar to show ticks between START and STOP (range 0..23)
 +
|-
 +
| hr20 toggle  SEG
 +
|  Toggle segment SEG (a number, not a symbolic name!)
 
|-
 
|-
 
| lcd backlight  STATE
 
| lcd backlight  STATE
Zeile 69: Zeile 99:
 
| ir send  DEVICE COMMAND
 
| ir send  DEVICE COMMAND
 
|  send COMMAND to DEVICE
 
|  send COMMAND to DEVICE
 +
|-
 +
|}
 +
== Infrared Send/Receive ([[IRMP]]) ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| irmp receive
 +
| receive an IR command
 +
|-
 +
| irmp send  PROTOCOL DEVICE COMMAND REPEAT
 +
|  send COMMAND with REPEAT flag to DEVICE using PROTOCOL
 
|-
 
|-
 
|}
 
|}
Zeile 129: Zeile 171:
 
| io set port  NUM HEXVALUE [MASK]
 
| io set port  NUM HEXVALUE [MASK]
 
|  Set the PORT NUM to VALUE (possibly using the provided MASK).
 
|  Set the PORT NUM to VALUE (possibly using the provided MASK).
 +
|-
 +
|}
 +
== Reading and Writing EEPROM Space on Device ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| eer eer <ADDR> <LENGTH>
 +
|  Read n bytes from address after the config in eeprom.
 +
|-
 +
| eew eew <ADDR> <HEXBYTES>
 +
|  Write Hexbytes at address after the config in epprom.
 +
|-
 +
| fuse
 +
| Display current fuse settings
 +
|-
 +
| hostname
 +
| Display hostname.
 
|-
 
|-
 
|}
 
|}
Zeile 166: Zeile 226:
 
|  Display the current date.
 
|  Display the current date.
 
|-
 
|-
−
| settime  UNIXTIME
+
| lastdcf
−
|  Set the current time (provide unix timestamp)
+
|  Display when last valid DCF Signal was received.
 
|-
 
|-
−
| time  
+
| time [UNIXTIME]
−
|  Display the current time in seconds since January 1st 1970.
+
|  Display/Set the current time in seconds since January 1st 1970.
 +
|-
 +
| uptime
 +
|  Display ethersex uptime in unix format.
 
|-
 
|-
 
| whm  
 
| whm  
Zeile 181: Zeile 244:
 
| ''Short description''
 
| ''Short description''
 
|-
 
|-
−
| sample
+
| sample  
 
|  Manually call application sample commands
 
|  Manually call application sample commands
 
|-
 
|-
Zeile 219: Zeile 282:
 
| cron_list  
 
| cron_list  
 
|  Show all cron entries
 
|  Show all cron entries
 +
|-
 +
| cron_make_persistent
 +
|  Mark a Job as persistent
 
|-
 
|-
 
| cron_rm  POSITION
 
| cron_rm  POSITION
 
|  Remove one cron entry
 
|  Remove one cron entry
 +
|-
 +
| cron_save
 +
|  Saves all persistent jobs
 +
|-
 +
|}
 +
== [[DALI]] ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| dali cmd  [TARGET] [COMMAND] [!][?]
 +
|  "send the given command (decimal) to targets (all, g00 to g15, s00 to s63), auto repeat with !, read reply with ?"
 +
|-
 +
| dali dim  [TARGET] [LEVEL]
 +
|  "dim targets (all, g00 to g15, s00 to s63) to given level (0-254)"
 +
|-
 +
| dali raw  [BYTE1] [BYTE2]
 +
|  "send a raw frame (two bytes, given in hex) over the DALI bus"
 +
|-
 +
| dali scmd  [SPECIAL COMMAND] [DATA] [!][?]
 +
|  "send special command (256-287) with data, auto repeat with !, read reply with ?"
 +
|-
 +
|}
 +
== [[DMX_Effect]] commands ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| dmx rainbow
 +
|  switch rainbow on (1) or off (0)
 +
|-
 +
| dmx random
 +
|  switch random on (1) or off (0)
 
|-
 
|-
 
|}
 
|}
−
== [[DMX]] ==
+
== [[DMX_Storage]] commands ==
 
{| border='1'
 
{| border='1'
 
| ''Command syntax''
 
| ''Command syntax''
 
| ''Short description''
 
| ''Short description''
 
|-
 
|-
−
| dmx fade
+
| dmx channels
−
| Fade DMX
+
| Get channels per universe
 
|-
 
|-
−
| dmx set6chan A B C D E F G
+
| dmx get
−
| Set DMX values
+
| Return channel value
 +
|-
 +
| dmx set
 +
|  Set channel values
 +
|-
 +
| dmx universe
 +
|  Get a whole universe
 +
|-
 +
| dmx universes
 +
|  Get universes
 
|-
 
|-
 
|}
 
|}
Zeile 333: Zeile 441:
 
| call  FILENAME
 
| call  FILENAME
 
|  Start script named FILENAME
 
|  Start script named FILENAME
 +
|-
 +
| cat  FILENAME
 +
|  cat file content (with debug only)
 
|-
 
|-
 
| dec  VAR
 
| dec  VAR
Zeile 369: Zeile 480:
 
| ''Command syntax''
 
| ''Command syntax''
 
| ''Short description''
 
| ''Short description''
 +
|-
 +
| fht send HOUSECODE ADDR CMD [CMD2]
 +
|  Send FHT command. See [[FS20]] for details.
 
|-
 
|-
 
| fs20 receive  
 
| fs20 receive  
−
|  Receive FS20 sequence and display it.
+
|  Receive FS20/FHT sequence and display it.
 
|-
 
|-
−
| fs20 send HOUSECODE ADDR CMD
+
| fs20 send HOUSECODE ADDR CMD [CMD2]
 
|  Send FS20 command. See [[FS20]] for details.
 
|  Send FS20 command. See [[FS20]] for details.
 
|-
 
|-
 
| fs20 ws300  
 
| fs20 ws300  
 
|  Receive FS20 sequence from WS300 weather station and decode it.
 
|  Receive FS20 sequence from WS300 weather station and decode it.
 +
|-
 +
|}
 +
== [[Frequency Counter]] ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| fc %duty  [CHANNEL]
 +
|  "returns last on duty cycle in percent  for given channel"
 +
|-
 +
| fc duty  [CHANNEL]
 +
|  "returns last on duty cycle (0-255)  for given channel"
 +
|-
 +
| fc freq  [CHANNEL]
 +
|  "returns last frequency in Hz for given channel"
 +
|-
 +
| fc off  [CHANNEL]
 +
|  "switch off frequency counting on given channel"
 +
|-
 +
| fc on  [CHANNEL]
 +
|  "switch on frequency counting on given channel"
 +
|-
 +
| fc ticks  [CHANNEL]
 +
|  "returns last frequency in CPU ticks for given channel"
 +
|-
 +
|}
 +
== [[GLCD_Menu]] ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| glcdmenu key  VALUE
 +
|  Send a keypress to the menu
 +
|-
 +
| glcdmenu update
 +
|  Update the menu
 
|-
 
|-
 
|}
 
|}
Zeile 390: Zeile 540:
 
| nmea satellites  
 
| nmea satellites  
 
| Get satellites
 
| Get satellites
 +
|-
 +
|}
 +
== [[H-Bridge]] ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| hbridge  [action] [enable_l] [enable_r]
 +
|  Set H-Bridge command
 +
|-
 +
| hbridge pwm  int
 +
|  Set H-Bridge enable line valueeg. speed
 
|-
 
|-
 
|}
 
|}
Zeile 397: Zeile 559:
 
| ''Short description''
 
| ''Short description''
 
|-
 
|-
−
| ds1631 start ADDR
+
| ds1631 convert ADDR VALUE
−
|  Initiate temperature conversions
+
|  Initiate temperature conversions (0: stop, 1: convert)
−
|-
 
−
| ds1631 stop ADDR
 
−
|  Stop temperature conversions
 
 
|-
 
|-
 
| ds1631 temp ADDR
 
| ds1631 temp ADDR
Zeile 412: Zeile 571:
 
| read byte from I2C chip
 
| read byte from I2C chip
 
|-
 
|-
−
| i2c rbd CHIPADDR DATAADDR
+
| i2c rbd CHIPADDR REGADDR
−
| read byte from address at I2C chip
+
| read byte from register address at I2C chip
 
|-
 
|-
−
| i2c rwd CHIPADDR DATAADDR
+
| i2c rwd CHIPADDR REGADDR
−
| read word from address at I2C chip
+
| read word from register address at I2C chip
 
|-
 
|-
 
| i2c wbb ADDR HEXVALUE
 
| i2c wbb ADDR HEXVALUE
 
| write byte to I2C chip
 
| write byte to I2C chip
 
|-
 
|-
−
| i2c wbd CHIPADDR DATAADDR HEXVALUE
+
| i2c wbd CHIPADDR REGADDR HEXVALUE
−
| write byte to address on I2C chip
+
| write byte to register address on I2C chip
 
|-
 
|-
−
| i2c wwd CHIPADDR DATAADDR HEXVALUE
+
| i2c wwd CHIPADDR REGADDR HEXVALUE
−
| write word to address on I2C chip
+
| write word to register address on I2C chip
 
|-
 
|-
 
| lm75 ADDR
 
| lm75 ADDR
Zeile 453: Zeile 612:
 
| pca9531 ADDR PERIODPWM1 DUTYPWM1 PERIODPWM2 DUTYPWM2 LED0..3 LED4..7
 
| pca9531 ADDR PERIODPWM1 DUTYPWM1 PERIODPWM2 DUTYPWM2 LED0..3 LED4..7
 
|  set PWM1 and PWM2 and LED states
 
|  set PWM1 and PWM2 and LED states
 +
|-
 +
| pca9685m ADDR
 +
|  OUTDRV, IVRT, PRESCALE
 +
|-
 +
| pca9685s ADDR
 +
|  LED, ON, OFF
 
|-
 
|-
 
| pcf8574x read ADDR CHIP
 
| pcf8574x read ADDR CHIP
Zeile 459: Zeile 624:
 
| pcf8574x set ADDR CHIP HEXVALUE
 
| pcf8574x set ADDR CHIP HEXVALUE
 
|  Set bits
 
|  Set bits
−
|-
 
−
| tsl2550 down
 
−
|  Set TSL2550 to power down state
 
 
|-
 
|-
 
| tsl2550 lux  
 
| tsl2550 lux  
−
|  Read ADC registers and compute light level
+
|  Show light level by reading adc registers and computing level
 
|-
 
|-
−
| tsl2550 mode VALUE
+
| tsl2550 mode VALUE
−
|  Set TSL2550 to standard or extended mode [std|ext]
+
|  Set the TSL2550s operating mode (0: standard range, 1: extended range)
 
|-
 
|-
−
| tsl2550 up
+
| tsl2550 power  VALUE
−
|  Set TSL2550 to power up state
+
|  Set the TSL2550s power state (0: down, 1:up)
 
|-
 
|-
 
|}
 
|}
−
== [[JABBER]] ==
+
== [[Jabber]] ==
 
{| border='1'
 
{| border='1'
 
| ''Command syntax''
 
| ''Command syntax''
Zeile 540: Zeile 702:
 
| pin toggle  NAME
 
| pin toggle  NAME
 
|  Toggle the status of pin NAME.
 
|  Toggle the status of pin NAME.
 +
|-
 +
|}
 +
== [[PWM]] ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| dtmf  CHARS
 +
|  send CHARS as DTMF
 +
|-
 +
| freq set  FREQUENCY DELAY
 +
|  Set frequency for DELAY ms
 +
|-
 +
| pwm fade  [channel +-diff startvalue]
 +
|  Set fading at channel with startvalue and change each stepp to diff (must be signed 3 digit)
 +
|-
 +
| pwm set  [channel value]
 +
|  Set channel to value
 
|-
 
|-
 
|}
 
|}
Zeile 585: Zeile 765:
 
| rfm12 external filter [1]
 
| rfm12 external filter [1]
 
|  Enable ext. filter pin if argument is present (disable otherwise)
 
|  Enable ext. filter pin if argument is present (disable otherwise)
 +
|-
 +
| rfm12 intertechno 
 +
|  family group device command
 
|-
 
|-
 
| rfm12 tevion   
 
| rfm12 tevion   
Zeile 590: Zeile 773:
 
|-
 
|-
 
|}
 
|}
−
== [[SD/MMC-Card-Reader]] ==
+
== [[SD-Karte]] ==
 
{| border='1'
 
{| border='1'
 
| ''Command syntax''
 
| ''Command syntax''
Zeile 630: Zeile 813:
 
| sms77_recv  [RECEIVER]
 
| sms77_recv  [RECEIVER]
 
|  SMS receiver
 
|  SMS receiver
 +
|-
 +
| sms77_type  [TYPE]
 +
|  SMS type
 
|-
 
|-
 
| sms77_user  [USERNAME]
 
| sms77_user  [USERNAME]
Zeile 650: Zeile 836:
 
|-
 
|-
 
|}
 
|}
−
== [[Sound]]/Melody support ==
+
== [[Sound]]/WAV support ==
 
{| border='1'
 
{| border='1'
 
| ''Command syntax''
 
| ''Command syntax''
 
| ''Short description''
 
| ''Short description''
−
|-
 
−
| pwm melody 
 
−
|  Play melody
 
 
|-
 
|-
 
| pwm stop   
 
| pwm stop   
 
|  Stop wav
 
|  Stop wav
 
|-
 
|-
−
| pwm wav   
+
| pwm wav  <FILENAME>
−
| Play wav
+
| Play wave file. Use VFS if compiled in. More details at [[Sound]]
 
|-
 
|-
 
|}
 
|}
Zeile 684: Zeile 867:
 
| stella store  
 
| stella store  
 
|  Store values in eeprom
 
|  Store values in eeprom
 +
|-
 +
|}
 +
== [[USB]] ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| keyboard  MESSAGE
 +
| Send MESSAGE as HID keyboard
 +
|-
 +
| mouse BUTTON DELTAX DELTAY
 +
| Send data as HID mouse
 
|-
 
|-
 
|}
 
|}
Zeile 699: Zeile 894:
 
| zac raw  PORT BIT
 
| zac raw  PORT BIT
 
|  Return raw hex temperature value of zacwire at BIT of PORT
 
|  Return raw hex temperature value of zacwire at BIT of PORT
 +
|-
 +
|}
 +
== lome6 ==
 +
{| border='1'
 +
| ''Command syntax''
 +
| ''Short description''
 +
|-
 +
| lome6 get_t  TYPE
 +
|  get temperature command
 +
|-
 +
| lome6 power  TYPE
 +
|  press power command
 +
|-
 +
| lome6 reset
 +
|  press reset command
 +
|-
 +
| lome6 set_t  TYPE TEMPERATURE
 +
|  set temperature command
 +
|-
 +
| lome6 state
 +
|  get state command
 +
|-
 +
| lome6 uptime  UPTIME
 +
|  set/get uptime command
 
|-
 
|-
 
|}
 
|}
Zeile 705: Zeile 924:
 
| ''Command syntax''
 
| ''Command syntax''
 
| ''Short description''
 
| ''Short description''
−
|-
 
−
| adc get  [CHANNEL]
 
−
|  Get the ADC value in hex of CHANNEL or if no channel set of all channels.
 
 
|-
 
|-
 
| alias list  
 
| alias list  
Zeile 715: Zeile 931:
 
| artnet test
 
| artnet test
 
|-
 
|-
−
| cw send   
+
| cw send  MESSAGE
−
|  Send Morce Code
+
|  Send MESSAGE in Morce Code
 
|-
 
|-
 
| d  ADDR
 
| d  ADDR
Zeile 726: Zeile 942:
 
| free  
 
| free  
 
|  Display free space.
 
|  Display free space.
−
|-
 
−
| fuse
 
−
| Display the fuse settings.
 
 
|-
 
|-
 
| help  
 
| help  
 
|  List which commands are available.
 
|  List which commands are available.
−
|-
 
−
| hostname
 
−
| Display hostname.
 
 
|-
 
|-
 
| ht  MESSAGE
 
| ht  MESSAGE
Zeile 741: Zeile 951:
 
| ipstats  
 
| ipstats  
 
|  Display IP statistics.
 
|  Display IP statistics.
−
|-
 
−
| keyboard  MESSAGE
 
−
| Send MESSAGE as HID keyboard
 
 
|-
 
|-
 
| mb recv   
 
| mb recv   
Zeile 750: Zeile 957:
 
| moodlight CHANNEL ONOFF
 
| moodlight CHANNEL ONOFF
 
|  Set CHANNEL moodlight on=1 or off=0. If no channel is given return on if channel CHANNEL is moodlighted
 
|  Set CHANNEL moodlight on=1 or off=0. If no channel is given return on if channel CHANNEL is moodlighted
 +
|-
 +
| motd [MESSAGE]
 +
| Save MESSAGE as new message of the day, otherwise just show current message
 
|-
 
|-
 
| msr1 get  
 
| msr1 get  
Zeile 766: Zeile 976:
 
| Push button identified by NUMBER
 
| Push button identified by NUMBER
 
|-
 
|-
−
| rfm12 intertechno  
+
| pwm melody [NUMBER]
−
|  family group device command
+
|  Play melody
 +
|-
 +
| sanyoz700  CMD
 +
|  Send command to projector
 
|-
 
|-
 
| sll get  
 
| sll get  
Zeile 775: Zeile 988:
 
|  Perform a memory test
 
|  Perform a memory test
 
|-
 
|-
−
| srf05
+
| srf05  
−
|  Get SRF05 Data
+
|  Read SRF05 measurement
 
|-
 
|-
 
| to1 get  
 
| to1 get  
Zeile 793: Zeile 1.006:
 
| Display the version number.
 
| Display the version number.
 
|-
 
|-
−
| wol  IP
+
| wol  MAC
−
| Send WAKE-ON-LAN command to IP
+
| Send WAKE-ON-LAN command to MAC
 +
|-
 +
| yport stats
 +
|  Report statistic counters
 +
|-
 +
| zbus stats
 +
|  Report statistic counters
 
|-
 
|-
 
|}
 
|}

Aktuelle Version vom 6. November 2011, 21:42 Uhr

This page is automatically generated from the files in the Ethersex source code repository. Do not edit this page but send patches for those files!


Analog/Digital Conversion (ADC)

Command syntax Short description
adc get [CHANNEL] Get the ADC value in hex of CHANNEL or if no channel set of all channels.
hr20 temp Read HR20 temperature sensor.

DNS Resolver

Command syntax Short description
dns server [IPADDR] Display/Set the IP address of the DNS server to use to IPADDR.
nslookup HOSTNAME Do DNS lookup for HOSTNAME (call twice).

Digital/Analog Conversion (DAC)

Command syntax Short description
ltc1257_delay `[VALUE] Set (if VALUE given) or get (no VALUE) delay for LTC1257 output bit changes in µs'
ltc1257_set `[VALUE0] [VALUE1] ... Set output to value (value: 0-4095)'
tlc5620 `[CHANNEL] [VALUE] Set Output to value (Value: 0-0xff)'

Fnordlicht

Command syntax Short description
fnordlicht "ADDRESS RED GREEN,BLUE",fnordlicht command to set RGB color
fnordlicht_init fnordlicht init

HD44780 LCD

Command syntax Short description
hr20 hourbar START STOP Update hourbar to show ticks between START and STOP (range 0..23)
hr20 toggle SEG Toggle segment SEG (a number, not a symbolic name!)
lcd backlight STATE switch back light STATE to ON or OFF
lcd char N D1 D2 D3 D4 D5 D6 D7 D8 Define use-definable char N with data D1..D8 (provide DATA in hex)
lcd clear [LINE] Clear line LINE (0..3) or the whole display (if parameter is omitted)
lcd goto LINE COL Move cursor to LINE and column COL (origin is 0/0)
lcd reinit CURSOR BLINK Reinitialize the display, set whether to show the cursor (CURSOR, 0 or 1) and whether the cursor shall BLINK
lcd shift DIR Shift the display to DIR (either left or right)
lcd write TEXT Write TEXT to the current cursor location

Infrared Send/Receive (IR-TRX)

Command syntax Short description
ir receive receive an IR command
ir send DEVICE COMMAND send COMMAND to DEVICE

Infrared Send/Receive (IRMP)

Command syntax Short description
irmp receive receive an IR command
irmp send PROTOCOL DEVICE COMMAND REPEAT send COMMAND with REPEAT flag to DEVICE using PROTOCOL

NTP Client

Command syntax Short description
ntp query Query the NTP server to get an NTP update.
ntp server [IPADDR] Display/Set the IP address of the NTP server to use to IPADDR.
ntp status Display NTP server status

Network configuration

Command syntax Short description
enc dump Dump the internal state of the enc to serial
gw [IP] Display/Set the address of the default router.
ip [IP] Display/Set the IP address.
mac [xx:xx:xx:xx:xx:xx] Display/Set the MAC address.
netmask [IP] Display/Set the network mask.

Port I/O

Command syntax Short description
io get ddr PORTNUM Display the current value of the DDR PORTNUM.
io get mask PORTNUM Display the mask of the port PORTNUM.
io get pin PORTNUM Display the current value of the PIN-register of the port PORTNUM.
io get port NUM Display the current value of the PORT NUM.
io set ddr PORTNUM HEXVALUE [MASK] Set the DDR of port PORTNUM to VALUE (possibly using the provided MASK).
io set port NUM HEXVALUE [MASK] Set the PORT NUM to VALUE (possibly using the provided MASK).

Reading and Writing EEPROM Space on Device

Command syntax Short description
eer eer <ADDR> <LENGTH> Read n bytes from address after the config in eeprom.
eew eew <ADDR> <HEXBYTES> Write Hexbytes at address after the config in epprom.
fuse Display current fuse settings
hostname Display hostname.

Resetting the controller

Command syntax Short description
bootloader Call the bootloader.
reset Reset the Ethersex.
wdreset Go into endless loop to trigger a watchdog timeout.

ADS

Command syntax Short description
ads get Get the ADC value in hex.
ads mean [COUNT] Get the mean of power of 2 COUNT ADC values in hex.

Clock

Command syntax Short description
date Display the current date.
lastdcf Display when last valid DCF Signal was received.
time [UNIXTIME] Display/Set the current time in seconds since January 1st 1970.
uptime Display ethersex uptime in unix format.
whm Display ethersex uptime.

Application_Sample

Command syntax Short description
sample Manually call application sample commands
sample_init Manually call application sample init method
sample_periodic Manually call application sample periodic method

MCUF

Command syntax Short description
mcuf modul N Select module N
mcuf modul list List all modules
mcuf showclock Show digital clock
mcuf showstring MESSAGE Show scrolling MESSAGE on the display

CRON-Dienst

Command syntax Short description
cron_add MIN HOUR DAY MONTH DOW ECMD Add ECMD to cron to be executed at given time
cron_list Show all cron entries
cron_make_persistent Mark a Job as persistent
cron_rm POSITION Remove one cron entry
cron_save Saves all persistent jobs

DALI

Command syntax Short description
dali cmd [TARGET] [COMMAND] [!][?] "send the given command (decimal) to targets (all, g00 to g15, s00 to s63), auto repeat with !, read reply with ?"
dali dim [TARGET] [LEVEL] "dim targets (all, g00 to g15, s00 to s63) to given level (0-254)"
dali raw [BYTE1] [BYTE2] "send a raw frame (two bytes, given in hex) over the DALI bus"
dali scmd [SPECIAL COMMAND] [DATA] [!][?] "send special command (256-287) with data, auto repeat with !, read reply with ?"

DMX_Effect commands

Command syntax Short description
dmx rainbow switch rainbow on (1) or off (0)
dmx random switch random on (1) or off (0)

DMX_Storage commands

Command syntax Short description
dmx channels Get channels per universe
dmx get Return channel value
dmx set Set channel values
dmx universe Get a whole universe
dmx universes Get universes

Dallas_1-wire_Bus

Command syntax Short description
1w convert [DEVICE] Trigger temperature conversion of either DEVICE or all connected devices
1w ds2450 convert [DEVICE] `start conversion (with optional input mask and read out control)'
1w ds2450 get [DEVICE] `get conversion result (one or all channels)'
1w ds2450 oc [DEVICE] `get/set output control (per channel)'
1w ds2450 oe [DEVICE] `get/set output enable (per channel)'
1w ds2450 por [DEVICE] `get/set power on reset (per channel)'
1w ds2450 power [DEVICE] `get/set power supply of device (global)'
1w ds2450 range [DEVICE] `get/set input voltage range (per channel)'
1w ds2450 res [DEVICE] `get/set bit resolution of AD convert (per channel)'
1w get DEVICE Return temperature value of onewire DEVICE (provide 64-bit ID as 16-hex-digits)
1w list Return a list of the connected onewire devices

DataFlash

Command syntax Short description
df status Display internal status.
fs format Format the filesystem.
fs inspect inode INODE Inspect INODE (and associated page).
fs inspect node NODE Inspect NODE and dump to serial.
fs list List the directory.
fs mkfile NAME Create a new file NAME.
fs remove NAME Delete the file NAME.
fs truncate NAME LEN Truncate the file NAME to LEN bytes.

DC3840 mobil camera support

Command syntax Short description
dc3840 capture Take a picture. Access 'dc3840' via VFS afterwards. See DC3840 Camera for details.
dc3840 light Light level of camera
dc3840 send A B C D E Send provided command bytes to the camera.
dc3840 sync Re-sync to the camera
dc3840 zoom Enable zoom of camera

ECMDScript

Command syntax Short description
call FILENAME Start script named FILENAME
cat FILENAME cat file content (with debug only)
dec VAR Decrement variable VAR (a number)
echo <any> Print out all arguments of echo
exit Exit currently running script
get VAR Get value of variable VAR
goto N Goto line N in currently running script
if ( CMD/VAR == CONST ) then CMD2 If condition matches execute CMD2
inc VAR Increment variable VAR (a number)
rem <any> Remark for anything
set VAR VALUE Set variable VAR to VALUE
wait I Wait I milliseconds

FS20

Command syntax Short description
fht send HOUSECODE ADDR CMD [CMD2] Send FHT command. See FS20 for details.
fs20 receive Receive FS20/FHT sequence and display it.
fs20 send HOUSECODE ADDR CMD [CMD2] Send FS20 command. See FS20 for details.
fs20 ws300 Receive FS20 sequence from WS300 weather station and decode it.

Frequency Counter

Command syntax Short description
fc %duty [CHANNEL] "returns last on duty cycle in percent for given channel"
fc duty [CHANNEL] "returns last on duty cycle (0-255) for given channel"
fc freq [CHANNEL] "returns last frequency in Hz for given channel"
fc off [CHANNEL] "switch off frequency counting on given channel"
fc on [CHANNEL] "switch on frequency counting on given channel"
fc ticks [CHANNEL] "returns last frequency in CPU ticks for given channel"

GLCD_Menu

Command syntax Short description
glcdmenu key VALUE Send a keypress to the menu
glcdmenu update Update the menu

GPS

Command syntax Short description
nmea get Get latitude and longitude data
nmea satellites Get satellites

H-Bridge

Command syntax Short description
hbridge [action] [enable_l] [enable_r] Set H-Bridge command
hbridge pwm int Set H-Bridge enable line valueeg. speed

I2C (TWI)

Command syntax Short description
ds1631 convert ADDR VALUE Initiate temperature conversions (0: stop, 1: convert)
ds1631 temp ADDR Read last converted temperature
i2c detect list detected I2C Chips
i2c rbb ADDR read byte from I2C chip
i2c rbd CHIPADDR REGADDR read byte from register address at I2C chip
i2c rwd CHIPADDR REGADDR read word from register address at I2C chip
i2c wbb ADDR HEXVALUE write byte to I2C chip
i2c wbd CHIPADDR REGADDR HEXVALUE write byte to register address on I2C chip
i2c wwd CHIPADDR REGADDR HEXVALUE write word to register address on I2C chip
lm75 ADDR Get temperature
max7311 getDDRw ADDR Get Direction-Register DDR
max7311 getINw ADDR Get Input-Register IN
max7311 getOUTw ADDR Get Output-Register OUT
max7311 pulse ADDR BIT TIME Toggle Output-BIT for TIME (in ms)
max7311 set ADDR BIT VALUE Set Output-BIT to VALUE (bool)
max7311 setDDRw ADDR VALUE Set Direction-Register DDR (VALUE as hex)
max7311 setOUTw ADDR VALUE Set Output-Register OUT (VALUE as hex)
pca9531 ADDR PERIODPWM1 DUTYPWM1 PERIODPWM2 DUTYPWM2 LED0..3 LED4..7 set PWM1 and PWM2 and LED states
pca9685m ADDR OUTDRV, IVRT, PRESCALE
pca9685s ADDR LED, ON, OFF
pcf8574x read ADDR CHIP Get bits
pcf8574x set ADDR CHIP HEXVALUE Set bits
tsl2550 lux Show light level by reading adc registers and computing level
tsl2550 mode VALUE Set the TSL2550s operating mode (0: standard range, 1: extended range)
tsl2550 power VALUE Set the TSL2550s power state (0: down, 1:up)

Jabber

Command syntax Short description
jabber_host [HOSTNAME] JABBER hostname
jabber_pass [PASSWORD] JABBER password
jabber_resrc [RESOURCE] JABBER resource
jabber_user [USERNAME] JABBER username

KTY

Command syntax Short description
kty autocalibrate CHANNEL Calibrate to 1000 Ohm precision Resistor.
kty cal get Return the calibration difference to 2k2 Resistor.
kty get [CHANNEL] Get the temperature in xxx.x °C of CHANNEL or if no channel set of all channels.

MotorCurtain commands

Command syntax Short description
curtain VALUE Set value of curtain. 0=closed..7=open. If you use fewer sensors, use the corrent value instead of 7.
curtainlast Return last known position
curtainmax Return maximum position
curtainoff Switch motor off

Named_PIN

Command syntax Short description
pin get NAME Read and display the status of pin NAME.
pin list List all known named-pins.
pin set NAME STATUS Set the status of pin NAME to STATUS.
pin toggle NAME Toggle the status of pin NAME.

PWM

Command syntax Short description
dtmf CHARS send CHARS as DTMF
freq set FREQUENCY DELAY Set frequency for DELAY ms
pwm fade [channel +-diff startvalue] Set fading at channel with startvalue and change each stepp to diff (must be signed 3 digit)
pwm set [channel value] Set channel to value

RFM12

Command syntax Short description
rfm12 reinit Re-initialize RFM12 module.
rfm12 setbandwidth BW Set RX bandwidth to BW.
rfm12 setbaud BAUD Set baudrate to BAUD.
rfm12 setdrssi DRSSI Set the drssi to DRSSI.
rfm12 setgain GAIN Set preamplifier gain to GAIN.
rfm12 setmod MOD Set modulation to MOD.
rfm12 status Display internal status.

RFM12_ASK

Command syntax Short description
rfm12 1527 housecodeCommand delay cnt
rfm12 2272 housecodeCommand delay cnt
rfm12 ask sense Trigger (Tevion) ASK sensing. Enable ext. filter pin before!
rfm12 external filter [1] Enable ext. filter pin if argument is present (disable otherwise)
rfm12 intertechno family group device command
rfm12 tevion housecode command delay cnt

SD-Karte

Command syntax Short description
sd dir List contents of current SD directory.
sd mkdir PATH Create directory hierarchy PATH.

SHT

Command syntax Short description
sht humid Return humidity of SHT sensor
sht raw Return raw hex temp (first line) and humidity value (second line) of SHT sensor
sht temp Return temperature of SHT sensor

SMS77

Command syntax Short description
sms77 MESSAGE Send MESSAGE to compiled in sms77 service
sms77_pass [PASSWORD] SMS77 password
sms77_recv [RECEIVER] SMS receiver
sms77_type [TYPE] SMS type
sms77_user [USERNAME] SMS77 username

PWM Servo Control

Command syntax Short description
pwm servo_dec SERVONR Decrement position of servo SERVONR
pwm servo_inc SERVONR Increment position of servo SERVONR
pwm servo_set SERVONR POSITION Set servo with SERVONR to POSITION

Sound/WAV support

Command syntax Short description
pwm stop Stop wav
pwm wav <FILENAME> Play wave file. Use VFS if compiled in. More details at Sound

Stella_Light commands

Command syntax Short description
channel CHANNEL VALUE FUNCTION Get/Set stella channel to value. Second and third parameters are optional. Function: You may use 's' for instant set, 'f' for fade and 'y' for flashy fade.
channels Return stella channel size
fadestep FADESTEP Get/Set stella fade step
stella load Load values from eeprom
stella store Store values in eeprom

USB

Command syntax Short description
keyboard MESSAGE Send MESSAGE as HID keyboard
mouse BUTTON DELTAX DELTAY Send data as HID mouse

ZACwire

Command syntax Short description
zac 306 PORT BIT Return temperature of TSic 306 at BIT of PORT
zac 506 PORT BIT Return temperature of TSic 506 at BIT of PORT
zac raw PORT BIT Return raw hex temperature value of zacwire at BIT of PORT

lome6

Command syntax Short description
lome6 get_t TYPE get temperature command
lome6 power TYPE press power command
lome6 reset press reset command
lome6 set_t TYPE TEMPERATURE set temperature command
lome6 state get state command
lome6 uptime UPTIME set/get uptime command

Miscelleanous

Command syntax Short description
alias list List all available aliases
artnet test artnet test
cw send MESSAGE Send MESSAGE in Morce Code
d ADDR Dump the memory at ADDR (16 bytes).
eeprom reinit Force reinitialization of the EEPROM config area
free Display free space.
help List which commands are available.
ht MESSAGE Send MESSAGE to compiled in httplog service
ipstats Display IP statistics.
mb recv Receive data from modbus
moodlight CHANNEL ONOFF Set CHANNEL moodlight on=1 or off=0. If no channel is given return on if channel CHANNEL is moodlighted
motd [MESSAGE] Save MESSAGE as new message of the day, otherwise just show current message
msr1 get Get data
mysql query QUERY Send specified MySQL query to the configured server
ns update net statistic for public anouncment of currently running ethersex
pam USER PASSWORD Use pam for user and password
push NUMBER Push button identified by NUMBER
pwm melody [NUMBER] Play melody
sanyoz700 CMD Send command to projector
sll get Request the logged data
sram memtest Perform a memory test
srf05 Read SRF05 measurement
to1 get Request data from sensor
tw MESSAGE Send MESSAGE to compiled in twitter service
upnp send Manually send UPnP broadcast packet
usart baud BAUD Set the USART baudrate to BAUD.
version Display the version number.
wol MAC Send WAKE-ON-LAN command to MAC
yport stats Report statistic counters
zbus stats Report statistic counters
Abgerufen von „http://old.ethersex.de/index.php?title=Ecmd_Reference&oldid=5225“